1. ANSI Z97.1, Safety Performance Specifications and Methods of Test for Safety Glazing Material Used In Buildings.
C. American Society for Testing and Materials (ASTM):
1. ASTM A 36, Specification for Structural Steel.
2. ASTM C 1036, Specification for Flat Glass.
3. ASTM C 1048, Specification for Heat Treated Flat Glass - Kind HS, Kind FT Coated and Uncoated Glass.
4. ASTM D 3647, Practice for Classifying Reinforced Plastic Pultruded Shapes According to Composition.
5. ASTM D 4216, Specification for Rigid Poly (Vinyl Chloride) (PVC) and Related Plastic Building Products Compounds.
6. ASTM E 90, Standard Test Method for Laboratory Measurement of Airborne Sound Transmission Loss of Building Partitions.
7. ASTM E 283, Test Method for Rate of Air Leakage Through Exterior Windows, Curtain Walls, and Doors.
8. ASTM E 330, Test Method for Structural Performance of Exterior Windows, Curtain Walls, and Doors by Uniform Static Air Pressure Difference.
9. ASTM E 413, Classification for Rating Sound Insulation.
10. ASTM E 547, Test Method for Water Penetration of Exterior Windows, Curtain Walls, and Doors by Cyclic Static Air Pressure Differential.
11. ASTM E 773, Test Method for Seal Durability of Sealed Insulating Glass Units.
12. ASTM E 774, Specification for Seal Durability of Sealed Insulating Glass Units.
13. ASTM F 476, Test Methods for Security of Swinging Door Assemblies.
D. Consumer Product Safety Commission (CPSC):
1. CPSC 16CFR-1201, Safety Standard for Architectural Glazing Materials.
E. National Fenestration Rating Council (NFRC):
1. NFRC 100, Procedure for Determining Fenestration Product Thermal Properties.
2. NFRC 200, Procedure for Determining Solar Heat Gain Coefficient.
F. National Wood Window & Door Association (NWWDA):
1. NWWDA Industry Standard I.S. 3, Industry Standard for Wood Sliding Patio Doors.
2. NWWDA Industry Standard I.S. 4, Industry Standard for Water-Repellent Preservative Treatment for Millwork.
3. NWWDA Industry Standard I.S. 8, Industry Standard for Wood Swinging Patio Doors.
1.04 PERFORMANCE REQUIREMENTS
A. Wood patio doors to comply with the minimum performance requirements specified in NWWDA Industry Standard I.S. 8, DP 40, when tested in accordance with NWWDA Industry Standard I.S. 3, except where more stringent requirements are specified.
** THE AIR INFILTRATION VALUE SPECIFIED BELOW IS FOR ANDERSEN HINGED PATIO DOORS AND IS MORE STRINGENT THAN THE MAXIMUM AIR INFILTRATION ALLOWABLE FOR NWWDA DP 40 PATIO DOORS. NWWDA DP 40 PATIO DOORS ALLOW A MAXIMUM AIR INFILTRATION OF 0.15 CFM/SF OF UNIT. **
B. Air Infiltration: When tested in accordance with ASTM E 283 at a static pressure of 1.57 psf, total air infiltration to average less than or equal to 0.04 cfm per square foot of unit.
C. Water Penetration: No water penetration beyond the interior face of patio door unit when tested in accordance with ASTM E 547 at a static pressure of 6.00 psf.
D. Structural Performance: No glass breakage, damage to hardware, or permanent deformation (set) which would cause any malfunction or impair the operation of the unit, or residual deflection greater than 0.1% of stile length when tested in accordance with ASTM E 330 at a positive and negative test pressure of 60 psf.
E. Design Criteria: Design and size patio door members to withstand positive and negative loads imposed by wind to a pressure of [______] psf when measured in accordance with ASTM E 330. Limit deflection to L/175.
F. Thermal Performance: Fenestration products shall have their thermal performance rated, certified and labeled in accordance with NFRC 100, and shall demonstrate maximum U-values as follows:
1. [Single Panel Doors:]
a. [Size AA (38" x 82"): High Performance, 0.32; High Performance Sun, 0.31.]
b. [Size BB (40" x 96"): High Performance, 0.32; High Performance Sun, 0.32.]
2. [Multiple Panel Doors:]
a. [Size AA (72" x 82"): High Performance, 0.32; High Performance Sun, 0.33.]
b. [Size BB (72" x 96"): High Performance, 0.32; High Performance Sun, 0.32.]
F. Sound Transmission Ratings: Patio doors to provide a sound transmission class (STC) of 34 when tested in accordance with ASTM E 90 and ASTM C 423.
G. Forced Entry Resistance: Patio units to comply with requirements for Grade 30 performance when tested in accordance with ASTM F 476 .
1.05 SUBMITTALS
A. Product Data, Installation Instructions, Detail Drawings and Samples: Submit the following under provisions of Section 01300 - Submittals:
1. Product Data: Submit manufacturer's product literature for all products and accessories furnished.
2. Installation Instructions: Submit manufacturer's installation instruction sheets for all products and accessories furnished.
3. Detail Drawings: Submit detail drawings indicating direction of swing, active and fixed panels, location and type of glazing material, and typical jamb, head and sill details.
B. Quality Control Submittals: Submit the following under provisions of Section 01400 -Quality Control:
1. Reference List: Submit reference lists as specified under Quality Assurance article.
C. Contract Closeout Submittals: Submit the following under provisions of Section 01700 -Contract Closeout:
1. Owner's Manual: Submit bound manual clearly identified with project name, location and completion date. Identify type and size of patio door units installed. Provide recommendations for periodic inspections, care and maintenance. Identify common causes of damage with instructions for temporary patching until permanent repair can be made.
1.06 QUALITY ASSURANCE
A. Manufacturer Qualifications: Company having at least 25 years experience in the manufacture of wood patio door products. Provide a reference list of at least 3 projects of similar scale and complexity successfully completed during the past three years. Provide project names, locations, completion dates, names and telephone numbers of General Contractor's and Owner's contact person.
B. Installer Qualifications: Company experienced in the installation of wood patio door products. Installer to provide a reference list of at least 3 projects of similar scale and complexity successfully completed during the past three years. Provide project names, locations, completion dates, names and telephone numbers of General Contractor's and Owner's contact person.
C. Safety Glazing: Comply with safety glazing requirements of ANSI Z97.1 and CPSC 16CFR 1201.
D. Insulating Glass Units: Provide insulating glass units permanently marked with certification label of Insulating Glass Certification Council (IGCC) indicating compliance with Class CBA.
1.07 DELIVERY, STORAGE AND HANDLING
A. In addition to general delivery, storage and handling requirements specified in Section 01600, comply with the following:
1. Deliver materials to job site in sealed, unopened cartons. Protect uncartoned units from damage.
2. Identify each carton with material name, date of manufacture and lot number.
3. Store patio doors and accessories off ground, under cover, protected from weather and construction activities.
1.08 PROJECT CONDITIONS
A. Install patio doors in strict accordance with safety and weather conditions required by manufacturer's product literature.
B. Extra caution must be exercised when temperature drops below 32 degrees F. and extreme care below 0 degrees F.
PART 2 PRODUCTS
2.01 MANUFACTURERS
A. Andersen Frenchwood Hinged Patio Door units as manufactured by Andersen Corporation, Bayport, Minnesota.
1. Color: [White] [Sandtone] [Terratone].
2.02 MATERIALS
A. Wood Members: Fabricated from a wood species approved in NWWDA Industry Standard I.S. 8.
B. Vinyl Cladding for Accessories: Rigid vinyl (PVC) complying with the requirements of ASTM D 4216, class 144434331111..
C. Reinforced Engineered Plastic: Comply with the requirements of ASTM D 3647.
D. Polyester Urethane Coating: High durability polyester urethane coating conforming to the requirements of AAMA 603.8.
E. Weatherstripping: Flexible Santoprene bulb compression type with welded corners.
F. Sill Cover: Zinc chromate and Polane coated aluminum extrusion.
G. Fastener Covers: Aluminum extrusion with urethane coating.
H. Sub-sill: Fibrex.
2.03 GLAZING
A. General: Tempered insulating glass units certified through the Insulating Glass Certification Council as conforming to the requirements of IGCC Class CBA when tested in accordance with ASTM E 773 and E 774. Provide dual sealed units consisting of polyisobutylene primary seal and silicone secondary seal. Metal spacers to have bent or soldered corners. Glass to be permanently labeled as conforming to the safety glazing requirements of ANSI Z97.1 and CPSC 16 CFR 1201.
** SELECT BETWEEN THE FOLLOWING STANDARD GLAZING OPTIONS. CONSULT ANDERSEN CORPORATION REPRESENTATIVE FOR ADDITIONAL GLAZING OPTIONS. **
B. High Performance (HP) Low Emissivity , Inert Gas Filled Insulating Glass Units:
1. Glass: Insulating glass units to consist of an inboard and outboard lite of clear, tempered glass conforming ASTM C 1048, Type 1, Class 1, q3, Kind FT.
2. High Performance (HP) LoE Coating: MSVD (magnetron sputtering vapor deposition) LoE coating applied to the No. 2 surface.
3. Inert Gas Filling: Fill space between glass lites with inert gas (argon) to reduce heat loss. Provide a minimum 97 percent initial fill level.
4. Performance Characteristics:
a. Center of Glass U-value: 0.25 maximum.
b. Visible Light Transmission: 71% minimum.
c. Ultra-violet Transmission: 15% +/- 1% .
d. Center of Glass SHGC: .42 +/- .02.
C. High Performance Sun II (HP Sun II) Low Emissivity, Inert Gas Filled Insulating Glass Units:
1. Glass: Insulating glass units to consist of an inboard and outboard lite of clear, tempered glass conforming ASTM C 1048, Type 1, Class 1, q3, Kind HS.
2. High Performance Sun II (HP Sun II) LoE Coating: Second generation MSVD (magnetron sputtering vapor deposition) LoE coating applied to the No. 2 surface.
3. Inert Gas Filling: Fill space between glass lites with inert gas (argon) to reduce heat loss. Provide a minimum 97 percent initial fill level.
4. Performance Characteristics:
a. Center of Glass U-value: 0.28 maximum.
b. Visible Light Transmission: 37% minimum.
c. Ultra-violet Transmission: 14% +/- 1%.
d. Center of Glass SHGC: .30 +/- .02.
2.04 HARDWARE
A. Hinges: Adjustable, captured hinge design with cover plate. Hinge to allow vertical and rack panel adjustment.
1. Finish: Zinc-dichromate protective finish with baked enamel paint finish.
** 6-PIN KEY CYLINDER IS OPTIONAL, INCLUDE IN FOLLOWING PARAGRAPH IF REQUIRED. **
B. Locks: Steel locking mechanism consisting of a lever operated latch and three point deadbolting lock mechanism. Three point locking system to consist of a 0.787" powder metal deadbolt which when projected will cause two additional hook bolts to engage inactive panel. Provide [6-pin key cylinder at exterior and ]thumb turn at interior.
1. Trim: Forged brass lever handle with brass escutcheon plate interior and exterior.
2. Finish: [[Bright brass] [Antique brass] finish with protective lacquer coating] [Bright chrome]. [PVD High Performance (Bright Brass Only)]
2.05 JOINING SYSTEMS
** ANDERSEN STRONGLY RECOMMENDS CONSULTATION WITH AN EXPERIENCED STRUCTURAL ENGINEER, ARCHITECT OR CONTRACTOR AND YOUR LOCAL ANDERSEN PATIO DOOR SUPPLIER OR REPRESENTATIVE WHEN SPECIFYING ANDERSEN JOINING SYSTEMS. **
A. Joining Systems:
1. Narrow Wood Fillers: Wood members treated with water repellent preservative after machining in accordance with NWWDA I.S. 4.
2. Steel Reinforcement Members: 4" x 3/16" thick hot rolled steel plate conforming to ASTM A 36 with zinc plating and yellow chromate conversion coat. Predrill holes for attachment to door frames.
3. Gusset Plates: Galvanized steel plates as recommended by patio door manufacturer for specific application.
4. Fasteners: Corrosion resistant screws as provided by patio door manufacturer for fastening reinforcement members and gusset plates to wood frame. All other fasteners are provided by patio door installer.
5. Head Flashing: 8" long sheet vinyl. Color to match patio door exterior.
6. Silicone Sealant: Silicone sealant as recommended by patio door manufacturer.
7. Vinyl Trim Strips: As recommended by patio door manufacturer for each joining method used. Color to match patio door unit exterior color.
2.06 ACCESSORIES
A. Grilles:
1. Interior Grilles: Removable, hardwood divided light grilles where indicated on Drawings. Removable interior grilles to install against interior glass, clipping onto metal fasteners attached to the sash. Provide dual face profile to give muntin bar appearance from both interior and exterior.
a. Finish: Unfinished.
b. Exterior Finish: [White] [Sandtone] [Terratone].
2. Exterior Grilles: Chlorinated polyvinyl chloride divided light grilles where indicated on Drawings. Permanently install grilles on exterior of glass to simulate true divided light muntin bars. Exterior grilles to be used in conjunction with interior grilles.
a. Exterior Finish: [White] [Sandtone] [Terratone].
B. Insect Screens: Provide hinged patio doors with an insect screen installed on the exterior.
1. Gliding Screen Door Frame: 0.040" roll formed aluminum frame with chromate conversion coating.
2. Hinged Screen Door Frame For Single Panel and Active Passive Units: 0.040" extruded aluminum frame with chromate conversion coating. Provide hinged screen doors complete with hinges, closers and latches.
5. Rollers: Insect screen doors to operate on Delrin injection molded bottom rollers with self contained leveling adjusters engaged in sill track. Provide Delrin injection molded, self adjusting rollers on top rail.
1. Exterior Trim and Casing: Where indicated on Drawings provide [1/2 inch] [3/4 inch] vinyl sheathed plywood conforming to U.S. Product Standards P.S. 1 and rigid vinyl channels. Color to match patio door framing.
a. [Perma-Shield casing to have 0.043" thick vinyl with lightly textured surface laminated with adhesive to 3/4" thick plywood] or [Vinyl laminated board to have 0.045" thick vinyl with smooth surface laminated with adhesive to 1/2" thick plywood].
b. Trim Channels: Rigid vinyl extrusions supplied by patio door manufacturer for use on same product line.
2. Support Mullion Trim: 2" wide wood filler and vinyl trim strip. Color to match patio door unit exterior color.
D. Exterior Extension Jambs: Two piece Polane coated 6063 aluminum extrusion with corner locks and drive rivet fastening system. Color to match patio door unit exterior color.
E. Sill Extender and sill support: Zinc chromate and Polane coated aluminum extrusion.
F. Extension Jambs: Solid Ponderosa Pine. Pre-drilled extension jambs for application (7-9/16" extension jambs not pre-drilled).
2.07 FABRICATION
A. Preservative Treatment: Treat wood frame and door panel wood members after machining with a water repellent preservative in accordance with NWWDA I.S. 4.
B. Frame Components:
1. Attach reinforced engineered plastic frame cover to wood sub-frame.
2. In-line wash and sensitize reinforced engineered plastic frame with a solvent base conductive preparation solution.
3. Factory apply urethane coating (2.6 mil. minimum dry film thickness) to exterior exposed surfaces of sensitized reinforced engineered plastic frame cover.
C. Door Panels:
1. Stiles and Top Rails: Finger jointed and edge glued wood core 1-1/2" thick before milling. Provide solid wood edge strips, phenolic interior and exterior outer substrate, and veneered interior surface.
2. Bottom Rails: Laminated construction consisting of spliced veneer interior surface over a finger jointed and edge glued wood core with a phenolic overlay interior and exterior outer substrate.
3. Door Panel Finish:
a. Interior: Unfinished natural clear pine to receive paint or stain finish as specified in Section 09900.
b. Exterior: Factory applied high durability urethane coating.
D. Corner Fastening: Double blind mortise and tenon joints secured with hardwood dowel and waterproof structural adhesive.
E. Sill: Zinc chromate and Polane coated, aluminum extrusion. Aluminum sill attached to composite Fibrex frame.
F. Weatherstripping: Factory apply gasket type weatherstripping to full perimeter of panels.
G. Glazing: Factory glaze with high performance glazing sealant and wood interior trim stops.
PART 3 EXECUTION
3.01 INSPECTION
A. Inspect opening before installation is commenced.
1. Verify rough opening or masonry opening is square and dimensions are correct. Verify sill plate is level.
2. Verify wood frame walls are dry, clean, sound and well nailed, and/or glued, free of voids and without offsets at joints. Ensure that nail heads are driven flush with all surfaces in opening and within 3" of rough opening.
3.02 PREPARATION
A. Open carton and remove patio door unit, parts and accessories. Inspect patio door. Verify that patio door unit is not damaged and all parts are included before disposing of carton.
B. Store patio door units in a safe place until installed.
C. For maximum protection, finish interior wood surfaces prior to or immediately after installation.
3.03 JOINING SYSTEMS
A. Assemble joining system where required for patio door and window combinations according to patio door manufacturer's instructions.
B. Apply corrosion resistant coating to cut ends and field drilled holes in steel reinforcement member.
C. Apply head flashing with silicone sealant at each vertical mullion head joint.
D. Attach gusset plates to rough opening as recommended by patio door manufacturer.
3.04 INSTALLATION
A. Install patio door units and accessories according to patio door manufacturer's installation instruction sheets.
B. Set units plumb, level true to line, without warp or rack in frames or panels.
C. Install batt insulation in shim space around perimeter of patio door to maintain continuity of building insulation. Do not use expanding foam insulation.
D. Extend vapor barrier to interior face of patio door frame and attach.
E. Install door hardware according to manufacturer's installation instructions. Check patio door for proper operation of locking mechanism.
F. Check door and screen operation. Adjust as recommended by patio door manufacturer to provide smooth operation without binding.
3.05 EXTERIOR FINISHING
A. Hold back exterior siding or other finish materials from edge of patio door unit to allow for expansion and contraction and the installation of a proper sealant joint with backing materials.
B. Seal perimeter of patio door after exterior finish is applied in accordance with the requirements of Section 07900.
C. Application of Vinyl Trim Strip to Wood Filler for Support Mullion:
1. Install according to patio door manufacturer's installation instruction sheets.
D. Application of Perma-Shield Casing and Vinyl Laminated Board and Rigid Channels:
1. Install according to patio door manufacturer's instructions.
3.06 ACCESSORIES
A. Grilles: Install grilles according to patio door manufacturer's installation instructions.
B. Screens: Install screens according to patio door manufacturer's installation instructions.
C. Extension Jambs: Install extension jambs according to patio door manufacturer's installation instructions.
3.07 INTERIOR FINISHING
A. Finish patio door interior wood components according to patio door manufacturer's instructions and requirements specified in Section 09900.
1. Finish patio door prior to installing trim set handle onto the locking mechanism.
3.08 CLEANING
A. Clean surfaces to remove dirt. Use cleaning materials specifically recommended by patio door manufacturer.
B. Protect glass and hardware from masonry cleaning solutions. Immediately flush patio door surfaces which come in contact with masonry cleaning solutions with clear water to prevent etching.
C. Remove debris from work site.
D. Leave patio door unit in a closed and locked position.
E. Protect interior and exterior of patio door units until structure is sealed from the weather.
